What causes the spa side error code to go away?

Depending on where the temp sensor is mounted; usually in the wall of the spa in a sensor mount, you could have a flow issue. Shut the spa down, remove the filter and make sure all the jets are open. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

What does the Oh message on the spa mean?

The spa is at a temperature above 108° . Do not use spa when temperature is flashing or the OH message is displayed. HLoH = Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. SEoP = Sensor open or disconnected.

What to do if your Spa is not overheating?

If your spa is not overheating and you are getting the above error codes then a couple of things need to be investigated. Depending on where the temp sensor is mounted; usually in the wall of the spa in a sensor mount, you could have a flow issue. Shut the spa power off, remove the filter and make sure all the jets are open.

What does it mean when spa is shut down?

SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected. Could indicate a flow problem. LF = Persistent low flow problems. (Displays on the 5th occurrence of “HFL” message with 24 hours).

What is the error code for the spa?

PSoL = Pressure switch open with low pump. PSoH = Pressure switch open with high pump. ToE = Time out error. Rare system error. Spa unusable. Contact ACC. OHH = Overheat. Spa has shut down. One sensor has detected 118º Fat heater. OHS = Overheat. Spa has shut down. One sensor has detected 110ºF. SnA = Spa is shut down.

When to use OH or hloh on Spa?

OH = Over heat. The spa is at a temperature above 108° . Do not use spa when temperature is flashing or the OH message is displayed. HLoH = Hi Limit Over Heat.

What does it mean when your Spa is deactivated?

Freeze protection. No action is necessary. Communication between the panel and circuit board is faulty. Watchdog” (spa is deactivated) A problem has been detected. Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). Open or shorted sensor ( heater disabled).

Which is the correct spa code for PSOL or psoh?

PSoL = Pressure switch open with low pump. PSoH = Pressure switch open with high pump. ToE = Time out error. Rare system error. Spa unusable.

Why does my Vita spa not turn on?

Overheating condition where a water temperature sensor has detected water temperatures of 110°F (43.3°C). Spa functioning is then disabled until temps fall below 108°F (42.2°C).Could indicate a pump operating at low speed for an extended time, constant filtering due to a programming error or a faulty pump. DO NOT GET INTO THE WATER!

Can You unsubscribe from a Vita spa email?

I can opt out at any time by selecting the unsubscribe option that appears at the bottom of every email. Vita Spas designed the industry’s first hot tub that was built to be appliance grade. They also utilize a steel frame as one of the essential building blocks for each of their products.

What to do if your Vita spa freezes?

Take off the heat shield cover to allow the water to cool down. Make sure that the slice valves are open and reprogram the spa to make sure there are no overlapping time cycles. Open all jets. Contact the dealer or service organization if the problem continues. Sensor detects possible freeze conditions.

What does cover guy on Vita spa stand for?

The Cover Guy provides all Vita Spa replacement covers so you are guaranteed a perfect fit every time. These are the error codes and display messages that a ThermoSpas Hot Tub may display, along with what they mean and any actions required: Stands for “Overheat”- and the tub shuts down.

What do you need to know about Vita spas?

Vita Spas designed the industry’s first hot tub that was built to be appliance grade. They also utilize a steel frame as one of the essential building blocks for each of their products. Their focus on hydrotherapy includes the same level of therapeutic relief that consumers would receive by visiting a massage therapist.

Is there an error code on my hot spring?

So, when you see an error code on your spa’s control panel, you might worry that you’ve lost your chance. But don’t fret! Hot Spring ® spa systems are reliable and will last a long time with regular maintenance, but issues do sometimes arise.

When do you get error code on your hot tub?

Updated on: December 23, 2020. Posted on: March 29, 2018. You likely look forward to a hot tub soak every day. So, when you see an error code on your spa’s control panel, you might worry that you’ve lost your chance. But don’t fret!

What to do if your spa heater does not turn on?

Turn on your spa and observe its operation. If you do not have power to the spa, you may have a tripped breaker panel switch or GFCI outlet. Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power. Turn the spa on.

What should I do if my spa heat cover is not working?

Remove spa heat cover to allow the water temp to cool down to 109ºF (43ºC). Call your service supplier or dealer if problem continues. Means that the system doesn’t detect any water pressure while pump is running. Check water level and open the water valves. Clean the spa filter or replace the spa filter if needed.

What should I do if my spa water is 107°F?

One of the sensors has detected that the spa water is 110°F. Remove spa cover and let the water cool down. At 107°F the spa should reset. If spa doesn’t reset there is an issue with sensors or PC board. Find replacement PC board. Potential freeze conditions.

Why are there error codes on my pump?

Other issues that can cause these error codes is debris wrapped around the pump impeller, or one of the valves is not open up all the way.

What happens if you fail to service a swim spa?

Failure to properly service or install spa related components can result in serious injury or death. DO NOT remove the protective covers from any electrical enclosure, or attempt to service any related electrical device, unless you are a qualified electrician or service professional.

What causes the spa side error code to go away?