What does code 170 on Jandy aquapure mean?
What does code 170 on Jandy aquapure mean?
Generates code 170 IF 188 is not present. VAC input voltage too low. Relay not conducting in the forward direction. Relay not conducting in the reverse direction. High cell current (at upper limit of A/D converter) and cell voltage falls below 19V. High cell current and cell voltage falls below 19V.
How to troubleshoot a Jandy aquapure error code?
1. Troubleshoot your tri-sensor to ensure it is working properly. 2. Clean or replace cell if necessary. 1. Check input voltage, transformer, and back board voltages. 2. Troubleshoot with Jandy or a licensed professional. 1. Check input voltage, transformer, and back board voltages. 2. Troubleshoot with Jandy or a licensed professional. 1.
What to do if you get a Jandy error code?
1. Recalibrate salt reading. 2. Backwash your filter if a DE filter is installed. 3. Partially drain your pool and dilute with fresh water until salinity level returns to 3.0. 1. Typically caused by low AC voltage from back board. Check the transformer and back board.
How to change a Jandy aquapure front board power supply?
Flow salinity sensor temperature probe error codes. 1.They all generates code 172- Flow sensor service is required. 2. Perform diagnostic test on board to ensure the board isn’t faulty. If not the board, the tri-sensor is the culprit. 3. How To Change a Jandy AquaPure Tri-Sensor Front board power supply is either too low or too high. 1.
What is code 172 on Jandy aquapure error code?
Salinity sensor sees less than .2 GPL of salt. Either there’s no salt in the pool or sensor is air locked. Flow salinity sensor temperature probe error codes. 1.They all generates code 172- Flow sensor service is required. 2. Perform diagnostic test on board to ensure the board isn’t faulty. If not the board, the tri-sensor is the culprit. 3.
What is the power supply code on Jandy aquapure?
Front board power supply either too low or too high. (Generates 173 – Low input voltage code if Level 2 code 188 is present) (Generates 170 code if 188 is not present) Contact a pool professional. VAC input voltage is too low.
1. Recalibrate salt reading. 2. Backwash your filter if a DE filter is installed. 3. Partially drain your pool and dilute with fresh water until salinity level returns to 3.0. 1. Typically caused by low AC voltage from back board. Check the transformer and back board.
Why is there an error code on my Jandy chlorine generator?
It becomes especially difficult if the product, like the Jandy AquaPure Chlorine Generator, only displays an error code, but not necessarily what the error code means nor solutions to the problem. If you purchased the unit a year ago, it’s quite possible you may have misplaced or thrown out the manual. How will you diagnose the issue then?
Generates code 170 IF 188 is not present. VAC input voltage too low. Relay not conducting in the forward direction. Relay not conducting in the reverse direction. High cell current (at upper limit of A/D converter) and cell voltage falls below 19V. High cell current and cell voltage falls below 19V.
What is the code for Jandy aquapure power supply?
1.They all generates code 172- Flow sensor service is required. 2. Perform diagnostic test on board to ensure the board isn’t faulty. If not the board, the tri-sensor is the culprit. 3. How To Change a Jandy AquaPure Tri-Sensor Front board power supply is either too low or too high. 1. Generates code 173- Low input voltage, IF code 188 is present.
Why is the salinity invalid on Jandy aquapure?
Cell current is 85% lower than desired and cell voltage above 19V. Salinity invalid due to out of range measurements caused by front board error. Although the charts should help narrow down the root to the issue on your Jandy AquaPure unit, it may not completely answer all your questions or concerns.
